- Uncle Ted's Guide To
- VDV (voice/data/video) Cabling
Termination
Also see our online "virtual hands-on" explanation of the termination processes of Cat 3/5/5E/6.
UTP cables are terminated with standard connectors
(plugs and jacks) or punchdowns. The plug/jack is often referred
to as a "RJ-45", but that is really a telco designation
for the "modular 8 pin connector" terminated with a
USOC pinout used for telephones. The male connector on the end
of a patchcord is called a "plug" and the receptacle
on the wall outlet is a "jack."
These terminations are called "IDC" for "insulation-displacement connections," by the way, since the wires are held in knife-edge terminations that slice through the insulation and dig into the copper wire, forming a tight seal.
In LANs, as spec'ed by 568, there are two possible pinouts, called T568A and T568B that differ only in which color coded pairs are connected - pair 2 and 3 are reversed. Either work equally well, as long as you don't mix them! If you always use only one version, you're OK, but if you mix A and B in a cable run, you will get crossed pairs!
The cable pairs are color coded as shown:
Each pair consists of a colored wire and a white wire with a matching color stripe. The stripe wire is "tip" and the solid color wire is "ring," referring to the tip of the old 1/4" telephone plug and the ring around the shaft that makes the connections.
Note: Plugs/jacks and punchdowns have different color codes! You cannot mix them up as they will result in wiremap errors - esp. split pairs which cause big problems with high speed transmission.
Jacks: The jacks are then terminated with these layouts, looking into the jack:
Note that the only difference between T568A and T568B is the reversal of pairs 2 and 3 - it's only a color code change.
Jacks usually have 110-style punchdowns on the back which can be terminated with punchdown tools, using special manufacturer's tools or even a snap-on cover for the connector. Again, you MUST keep the twists as close to the receptacle as possible to minimize crosstalk.
Note: Cat 3 jacks and all plugs are going to
use these color codes shown above. 
However, Cat 5, 5e and 6
jacks have internal connections that continue the twists as close
to the pins in the jacks as possible. Thus the pinout on the
back of the jacks will not usually follow the standard color
code layouts- see the pin sequence in the photo above and the
twists in the internal connections of the jack here!
Remember: Always follow the color codes on the back of the jacks to insure proper connections!
Plugs: The plugs are terminated by straightening our the wires in proper order and crimping on a connector. Like we said before, you MUST keep the twists as close to the plug as possible to minimize crosstalk.
Patchcords: They generally use stranded wire for flexibility but can be made with solid wire for higher performance. Note that plugs may be different for each type of wire, so make sure you have the right type.
Crossover Cables: Normal cables that connect a PC/NIC card to a Hub are wired straight through. That is pin 1 is connected to pin 1, pin 2 to pin 2, etc. However, if you are simply connecting two PCs together without a hub, you need to use a crossover cable made by reversing pair 2 and 3 in the cable, the two pairs used for transmisson by Ethernet. The easy way to make a crossover cable is to make one end to T568A color coding and the other end to T568B. Then the pairs will be reversed.
Punchdowns
Sometimes there are cross connects using punchdowns in the telecom closet, more common on telephone wires than data. These are called punchdowns because the cable is punched down into the IDC contacts with a special tool, called (surprise!) a punchdown tool. Of course, you MUST keep the twists as close to the punchdown as possible to minimize crosstalk.
Punchdowns come in 4 varieties:
110, 66, Bix and Krone. Most popular for LANs is the 110 , for
telcos it's the 66, and the Bix and Krone are rare (price, proprietary
designs, etc.)
110 block (left) 66 block (right)
Color Codes For Punchdowns:
Punchdowns of all types are always
made with the pairs in order with the white/stripe wire (tip)
first, then the solid colored wire (ring). 
- Pair 1(w/blue-blue)
- Pair 2 (w/orange-orange)
- Pair 3 (w/green-green)
- Pair 4 (w/brown-brown)
- Pair 2 (w/orange-orange)
(This color code is often remembered by BLOG - BLueOrangeGreen and brown is all that's left!)
Refer to our online "virtual hands-on" explanation of the termination processes of Cat 3/5/5E/6 for complete illustrated procedures.
Patch Panels
Patch panels offer the most flexibility
in a telecom closet. All incoming wires are terminated to the
back of the patch panel on 110-style punchdowns (again watching
the 1/2 inch limit of untwisting pairs). Then patch cables are
used to interconnect the cables by simply plugging into the proper
jacks. 
Patch panels can have massive number of cables, so managing these cables can be quite a task in itself. It is important to keep all cables neatly bundled and labeled so they can be moved when necessary. However, it is also important to maintain the integrity of the cables, preventing kinking or bending in too small a radius which may adversely affect frequency performance.
(Note: Cat 6 cabling is physically larger in diameter than Cat 5e and usually has a separator for the pairs. The cable construction makes the cable stiffer and more prone to kinking, requiring a larger bend radius.)
